Mercedes of the S-class W202

1993-2000 of release

Repair and operation of the car



Mercedes W202
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Lubrication system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. System of ignition
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
- 13. Body
   13.2. Forward door
   13.3. Back door
   13.4. Handle of a forward door
   13.5. Handle of a back door
   13.6. Door lock
   13.7. Internal covering of doors
   13.8. Forward window regulator
   13.9. Glass of a forward window
   13:10. Back window regulator
   13:11. Glass of a forward door
   13:12. Window regulator engine
   13:13. Glove boxing
   13:14. Gear shifting handle sheeting
   13:15. Forward ashtray
   13:16. Average console
   13:17. Heating service panel
   13:18. Internal covering of the A-rack
   13:19. Internal covering of the S-rack
   13:20. Front seat
   13:21. Back seat
   + 13:22. Central lock
   13:23. External mirror / glass of a mirror
   13:24. A covering under the dashboard
   13:25. Front bumper
   13:26. Rear bumper
   13:27. Internal wing of the car
   13:28. Car wing
   13:29. Lattice Mercedes radiator / emblem
   13:30. Draft of a cowl of the engine
   13:31. A covering under a windshield
   13:32. The air supply device for heating of salon
   13:33. Catchment basin
   13:34. Paint and varnish covering
   13:35. Metal corrosion
   13:36. Automake-up
   13:37. What creaks?
   13:38. Hatch
+ 14. Electric equipment
+ 14.2. Electrical circuitries





13.7. Internal covering of doors

GENERAL INFORMATION

Driver's door

1. Window regulator handle
2. Lock socket
3. Deepening for the handle
4. Covering
5. Internal covering of a door
Instruction: on back doors it is necessary to carry out work as appropriate

Removal

PERFORMANCE ORDER
1. Unscrew the socket of the lock (2) the screw-driver and remove it.
2. Completely lower door glass by means of the handle.
3. Remove the window regulator handle for what the small screw-driver press a lock hook on a covering. Lower a covering in the direction of an arrow down and remove.
4. Remove the handle from an axis, remove an expansion washer.
5. Blendu (3) for actuating of a door disconnect fingers or the screw-driver from an internal covering of a door from within and remove.
6. Unscrew the screw (6) on the mechanism of management of a door from within.
7. Wring out a covering (4) under an armrest in a door pocket and unscrew the screw with crosswise shliyets on a head.
8. Circularly slightly disconnect an internal covering of a door from a door tin.
9. Wring out a covering of a door from a door tin from the lower party and sideways the wide pallet or the screw-driver, at the same time disconnect spring clips. To begin with the lower party of a covering.
Prevention

Lay material not to scratch a varnish.


10. Open a stopper (7) of the mechanism of actuating of a door from within and disconnect the mechanism (8). At "electrically an adjustable seat of the driver" instead of the mechanism flexible draft is built in, disconnect it.
11. Disconnect the wire plug from a door covering.
12. Pull an internal door covering over the button of blocking of a door up and take from a door tin.

Installation

PERFORMANCE ORDER
1. Before assembly track the correct installation of the pressurizing film. Small damages of a film tape, at big cracks replace a film.
Prevention

At the plant the holder of fastening of an armrest priklepyvatsya only after installation of a film. When replacing a film cut out this area and stick a vnakhlestka or condense with the gluing tape.


2. Put on the wire socket.
3. Insert the mechanism of actuating of a door from within and record it.
4. Replace the damaged spring clips. Establish an internal covering from above over the button of blocking of a door, enter into the tire for a sealant and along with spring clips in openings in a door tin.
5. Press fists an internal covering of a door in the field of spring clips.
6. Twist the screw with crosswise shliyets below an armrest. Impose a covering.
7. Fasten management of a door of two screws from within. Impose a handle cover.

8. (3) handles of a window regulator establish a gap washer by big diameter to a door covering.
9. Get the handle on an axis. At an open window the handle has to be directed obliquely forward up.
10. Pull from below a cover (1) over the handle (2), at the same time track that the head of a cover entered a flute on a handle axis. Advance a covering so, the fixing hooks (shooter) will not enter gearing yet.
11. Raise glass by means of the handle up.
12. Insert a covering for the door lock from above and from below fix by the screw.