Mercedes of the S-class W202

1993-2000 of release

Repair and operation of the car



Mercedes W202
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Lubrication system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. System of ignition
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
- 13. Body
   13.2. Forward door
   13.3. Back door
   13.4. Handle of a forward door
   13.5. Handle of a back door
   13.6. Door lock
   13.7. Internal covering of doors
   13.8. Forward window regulator
   13.9. Glass of a forward window
   13:10. Back window regulator
   13:11. Glass of a forward door
   13:12. Window regulator engine
   13:13. Glove boxing
   13:14. Gear shifting handle sheeting
   13:15. Forward ashtray
   13:16. Average console
   13:17. Heating service panel
   13:18. Internal covering of the A-rack
   13:19. Internal covering of the S-rack
   13:20. Front seat
   13:21. Back seat
   + 13:22. Central lock
   13:23. External mirror / glass of a mirror
   13:24. A covering under the dashboard
   13:25. Front bumper
   13:26. Rear bumper
   13:27. Internal wing of the car
   13:28. Car wing
   13:29. Lattice Mercedes radiator / emblem
   13:30. Draft of a cowl of the engine
   13:31. A covering under a windshield
   13:32. The air supply device for heating of salon
   13:33. Catchment basin
   13:34. Paint and varnish covering
   13:35. Metal corrosion
   13:36. Automake-up
   13:37. What creaks?
   13:38. Hatch
+ 14. Electric equipment
+ 14.2. Electrical circuitries





13.4. Handle of a forward door

GENERAL INFORMATION

1. Door handle
2. Lock cylinder guide
3. Rotary core
4. Laying
5. Laying
6. A bolt with an internal hexagon of 4 mm
7. The holding bracket for a bolt
8. Basic bracket
9. Screws

Removal

PERFORMANCE ORDER
1. Get a door sealant at height of the door lock of a groove of a door.
2. Turn off approximately on 4 turns a bolt with an internal hexagon (6) by means of 4 mm of a face key through an opening at doors. The bolt with an internal hexagon is insured against drop-out by the holder (7).
3. (2) extend a guide at first back, and then outside.
4. Extend the door handle (1) with laying (4) from a basic bracket back and remove. The basic bracket can be removed, in case of need, from the inside of a door, but for this purpose it is necessary to remove a door covering.
5. Remove laying (5).

Installation

Door lock

2 – lock cylinder guide
3 – rotary core
10 – eccentric adjusting screw
11 – door lock
12 – the operating lever

11 – door lock
13 – an opening under the eccentric adjusting screw
14 – an opening under the screw with an internal hexagon

PERFORMANCE ORDER
1. Install the eccentric regulating screw (10) outside thanks to what the door handle is easier mounted.
2. Install the door handle with laying and at the same time enter into the operating lever (12) of the door lock.
3. Behind insert a guide of the cylinder of the lock (2) and also enter a rotary core (3) into control of the door lock.
4. Fix the door lock by a bolt with an internal hexagon.
5. Adjust by means of the eccentric screw (10) a gap between the handle (1) and the operating lever (12) the crosswise screw-driver through an opening (13) on the forward party of a door. The gap has to make from 1 to 3 mm.
6. Insert a sealant of a door and check work of a door.